- _ -

• _GET_INPUT : arduino.h , extruder/arduino.h , extruder/temp.h , extruder/heater.h
• _GET_OUTPUT : extruder/temp.h , arduino.h , extruder/arduino.h , extruder/heater.h
• _READ : arduino.h , extruder/arduino.h , extruder/heater.h , extruder/temp.h
• _SET_INPUT : extruder/temp.h , arduino.h , extruder/arduino.h , extruder/heater.h
• _SET_OUTPUT : extruder/heater.h , arduino.h , extruder/arduino.h , extruder/temp.h
• _TOGGLE : arduino.h , extruder/temp.h , extruder/heater.h , extruder/arduino.h
• _WRITE : arduino.h , extruder/heater.h , extruder/arduino.h , extruder/temp.h

- a -

• ACCELERATION_RAMPING : config.gen3.h , config.gen6.h , config.ramps.h
• ACCELERATION_STEEPNESS : config.gen3.h , config.gen6.h , config.ramps.h
• ASCII_XOFF : serial.c
• ASCII_XON : serial.c

- b -

• BAUD : config.gen3.h , config.gen6.h , config.ramps.h
• buf_canread : serial.c
• buf_canwrite : serial.c
• buf_pop : serial.c
• buf_push : serial.c
• BUFSIZE : serial.c

- c -

• CDC_NOTIFICATION_EPNUM : Descriptors.h
• CDC_NOTIFICATION_EPSIZE : Descriptors.h
• CDC_RX_EPNUM : Descriptors.h
• CDC_TX_EPNUM : Descriptors.h
• CDC_TXRX_EPSIZE : Descriptors.h
• crc : gcode_parse.c

- d -

• DEFAULT_D : heater.c , extruder/heater.c
• DEFAULT_I : extruder/heater.c , heater.c
• DEFAULT_I_LIMIT : heater.c , extruder/heater.c
• DEFAULT_P : extruder/heater.c , heater.c
• DEFINE_HEATER : heater.c , extruder/heater.c
• DEFINE_TEMP_SENSOR : extruder/analog.c , analog.c , extruder/temp.c , temp.c

- e -

• E_STARTSTOP_STEPS : config.gen3.h , config.ramps.h , config.gen6.h

- g -

• GET_INPUT : arduino.h , extruder/arduino.h , extruder/temp.h , extruder/heater.h
• GET_OUTPUT : arduino.h , extruder/temp.h , extruder/arduino.h , extruder/heater.h

- h -

• HEATER_EXTRUDER : config.gen6.h , config.ramps.h
• HOST : config.gen6.h , config.gen3.h , config.ramps.h

- l -

• LEDMASK_USB_ENUMERATING : lufa_serial.h
• LEDMASK_USB_ERROR : lufa_serial.h
• LEDMASK_USB_NOTREADY : lufa_serial.h
• LEDMASK_USB_READY : lufa_serial.h

- m -

• MASK : arduino.h , extruder/arduino.h , extruder/temp.h , extruder/heater.h
• MAXIMUM_FEEDRATE_X : config.ramps.h , config.gen3.h , config.gen6.h
• MOVEBUFFER_SIZE : config.ramps.h , config.gen6.h , config.gen3.h

- p -

• PID_SCALE : config.gen3.h , config.ramps.h

- r -

• READ : arduino.h , extruder/arduino.h , extruder/temp.h , extruder/heater.h
• REFERENCE : config.gen3.h , config.ramps.h
• REPRAP_HOST_COMPATIBILITY : config.ramps.h , config.gen6.h , config.gen3.h

- s -

• SEARCH_FEEDRATE_X : config.gen3.h , config.gen6.h , config.ramps.h
• SET_INPUT : arduino.h , extruder/arduino.h , extruder/heater.h , extruder/temp.h
• SET_OUTPUT : extruder/temp.h , arduino.h , extruder/arduino.h , extruder/heater.h
• STEP_INTERRUPT_INTERRUPTIBLE : config.gen6.h , config.ramps.h , config.gen3.h
• STEPS_PER_MM_E : config.ramps.h , config.gen3.h , config.gen6.h

- t -

• TEMP_HYSTERESIS : config.gen3.h , config.gen6.h , config.ramps.h
• TEMP_RESIDENCY_TIME : config.gen3.h , config.gen6.h , config.ramps.h
• TEMP_THERMISTOR : config.ramps.h , config.gen6.h
• TH_COUNT : config.gen3.h , config.ramps.h
• TICK_TIME : timer.c , extruder/timer.c
• TICK_TIME_MS : timer.c , extruder/timer.c
• TOGGLE : extruder/heater.h , extruder/temp.h , arduino.h , extruder/arduino.h
• TX_ENABLE_PIN : config.gen3.h

- u -

• UM_PER_STEP_E : dda.c
• UM_PER_STEP_X : dda.c
• UM_PER_STEP_Y : dda.c
• UM_PER_STEP_Z : dda.c

- w -

• WRITE : arduino.h , extruder/temp.h , extruder/heater.h , extruder/arduino.h

- x -

• X_MIN : config.gen3.h , config.ramps.h , config.gen6.h